Utilities Companies Adopt Cost-Effective 5G and 4G IoT Connectivity For Smart Meters
August 28, 2020

To connect their smart meters, utilities companies are moving away from what they’ve traditionally used—mesh technology such as Wi-SUN® with distributed access points—toward 3GPP standardized 4G and 5G cellular. This is because the price of 4G LTE modules and chipsets has dropped significantly now that LTE networks are universally available and volume pricing has come into play. While Wi-SUN technology may have been the best option for connecting utility meters in the past, today the advantages of cellular have upended this paradigm and introduced a new economic environment in which cellular has become the better choice to connect smart utility meters — better in cost, scale, and efficiency.


In the early days of 4G, the cost of an LTE M2M module was approximately $100, and available from only one source. At that time, there were no unlimited data plans available from any of the carriers and 2G/3G technology was notoriously power hungry, requiring large, expensive batteries. Mesh technologies, such as Wi-SUN, were used because the technology was cheaper than cellular, there were no issues with respect to data plans, and power usage could be optimized well-enough for a specific smart meter use case.

With the advent of LTE-M, defined by 3GPP in Release 13 and created specifically for low power wide area (LPWA) networks for IoT, the landscape has changed entirely. There are today more than a dozen companies developing LTE-M chipsets, and more than a dozen module makers using those chipsets, and there are a multitude of data plans offered by the major carriers to IoT companies, including utility providers, and MNOs/MVNOs, all working to drive costs down across the ecosystem. Highly efficient LTE-M technology also solved the power consumption issue.


While mesh technology is limited in its ability to scale, LTE-M has no such limitation and can scale with virtually no limit—a capability that will continue to drive down prices in the coming years. Mesh requires utility companies to deploy their own networks and bear all the burden of maintaining and upgrading those networks at an ever-increasing cost that drives the total cost of ownership up and up. Today, LTE-M is available at nearly 99 percent coverage in the USA from leading operators AT&T, T-Mobile, and Verizon so there is no longer any need for utility companies to build and maintain their own mesh networks.


Cities and other municipalities who are customers of utility companies, are now looking at more comprehensive smart city initiatives that include infrastructure, public safety, transportation, streetlights, parking meters, and more. This evolution creates an opportunity for utility companies to capture more revenue from their customers by expanding their services beyond smart metering to smart city services. Spending time developing and expanding business and increasing TAM (total available market) instead of spending money on developing infrastructure, modules and software, enables utility companies to create new revenue streams and increase efficiencies in the ever-expanding smart city market.

Monarch SiP — The Sequans Solution for Smart Meters

We at Sequans, together with our partner, Skyworks, have brought to market a powerful solution for the smart meter market called Monarch SiP—an LTE-M connectivity module that was developed with utility meters in mind, particularly water and gas meters, which require specific packaging capabilities and a very high level of reliability due to their typically harsh and corrosive environments. Monarch SiP combines Sequans’ Monarch LTE-M chipset with the universal radio front end of Skyworks in the world’s smallest package that is ultra-low in power consumption, and ultra-high in reliability and coverage, resulting in an LTE-M connectivity solution that is ideal for water and gas smart meters.

Power Consumption

Sequans has achieved ultra-low PSM (power saving mode) power consumption of 1µA at rock bottom, which is the lowest in the industry and three times better than the nearest competitor. This means that in eDRX mode where the meter wakes up, for example, every 20 minutes, a Sequans device is able to sleep at this 1µA level for 19 minutes and 56 seconds (assuming 4 seconds of active time). This allows meter companies to scale down the size of their batteries significantly, reducing battery cost while offering longer battery life. Since many water and gas meters are expected to live 20 years in the field, they have traditionally carried sizeable and expensive batteries. But, using Monarch SiP, many of our customers have been able to reduce their battery size by half and in some cases even more.

A power consumption comparison between a Sequans module and a competitor module (claiming 3µA power consumption at rock bottom) has recently been conducted. In the figure below, the top section shows the power consumption of a Sequans’ Monarch-based module and the bottom section shows the power consumption of a competitor’s module. The results show the Sequans device with average power consumption of 1.27µA while the competitor’s device shows an average of 20.4µA.

A power consumption comparison chart between two productsThe power consumption comparison was also made using an eDRX cycle with a 5-minute interval. In the figure below, results show that the Monarch GM01Q device consumes half as much power as the competitor’s device. Even when the eDRX cycle interval is increased (a case not uncommon for meters and battery-operated devices), the Monarch GM01Q power consumption advantage is seen to be even more significant at 75 percent better than the competitor’s device.

Power Consumption Chart Comparing two devices


Monarch SiP is one of the most reliable solutions in the market today. Gas contains sulfur and water creates humidity, both of which have an adverse effect on standard modules that contain silver in the shielding. Monarch SiP is uniquely silver-free making it an ideal solution for the harsh environments present with gas and water meter installations. The lower corrosion rates enabled by Monarch SIP enable long-term deployments of 20 years or more, with fewer truck rolls. While it is true that metering companies can design and build their own protective technology to ensure no sulfur or humidity pockets form close to their devices, the use of Monarch SiP eliminates this added expense, which companies can then use for R&D or value-added services. Additionally, Monarch SiP can be purchased with an even higher reliability package option where certain pins are placed in strategic locations to eliminate potential issues of package warpage or loosening of the solder that mates the package balls to the PCB. The use of this package enables customers to reduce issues related to vibration—a distinct advantage over the alternative use of hard epoxy materials.


Coverage is an important consideration for the metering industry since meters are not mobile and are usually located in deep indoor locations and sometimes at the cell edge where RF signals may be attenuated. Monarch SiP uses 23dBm transmission power, which reduces the need for repetition and retransmission and can partially compensate for RF signal loss. Repetition and retransmission require that a system be awake for longer periods of time, reducing the life of battery-operated gas and water meters. In some cases, devices that don’t have 23dBm power at the cell edge will not be able to transmit even with repetitions and retransmissions. Monarch SiP with its 23dBm power capability provides superior coverage in deep indoor, buried, and cell-edge implementations.


Monarch SiP is an ideal solution for gas and water smart meters. In addition to its ultra-high reliability and ultra-low power consumption, it is a proven and mature solution certified by leading operators all over the world. Monarch SiP is cost-effective. Even with its high-end capabilities, it is competitive in cost with most standard M2M modules. Finally, its size is the smallest in the world when compared to competing devices with similar capabilities. Measuring only 8.8 mm by 10.8 mm x 0.95 mm, it can fit into the smallest of devices.

Sequans is the leader in LTE-M chips and modules and a company 100 percent focused on IoT. To learn more about how Sequans’ Monarch SIP can bring your IoT project to life, please contact us at sales@sequans.com.

Recent Posts

What is Massive IoT?

Only Cellular Connectivity Will Do Massive IoT describes the hundreds of billions of things that are connected to the internet and collecting and transmitting small amounts of data from sensors. Processing the data from these connected things with AI and machine...

New Business Models Enabled by iSIM

Olivier Amiot, senior director of product marketing at Sequans, discussed iSIM with industry leaders at Kigen’s iSIM Pioneers summit in London, October 25. On the panel with him were Jean-Philippe Betoin of Kigen, Matt Hatton of Transforma Insights, and Paul Marshall...

T-Mobile Certifies Sequans Monarch 2 GM02S LTE-M/NB-IoT Module

Industry’s most advanced cellular IoT solution now ready to connect T-Mobile IoT customers Sequans’ 5G cellular IoT module, Monarch 2 GM02S, delivering LTE-M and NB-IoT connectivity, is now certified by T-Mobile and ready to bring new IoT devices to life for...

Recent Blog Posts

Find the Chip or Module That's Perfect for Your Application

Sequans has a solution for every type of IoT application from the smallest sensor device to the most sophisticated voice activated alarm system.